OXITEC 5000+

QAL1

Suitability Tested according to EN 15267 QAL1 Certified

Certificate only on request

OXITEC 5000+

MCERTS

MCERTS Performance Standards for Continuous Emission Monitoring Systems, Version 3.5

Certificate only on request

DIN ISO 9001 Certificate

ANAB

Quality management system, meets the requirements of BS EN ISO 9001
(BSI British Standards Institution, United Kingdom)

Certificate only on request

SCC Certificate

SCC

"Safety Certificate Contractors" SCCP for service, maintenance and on-site repair of gas analyzer systems, installation and commissioning of emission and operational measurements.

Certificate only on request

Certificate TÜV Suitability Test

TÜV

Oxygen measurement OXITEC® 500E / SME5 TÜV suitability test for DIN EN 14181 and DIN EN ISO 14956. The measuring device complies with the requirements of QAL 1. This certificate is only valid for current installations.
(TÜV Rheinland, Cologne)

Certificate only on request

ATEX Certification

ATEX

OXITEC® / COMTEC® electronic unit SME-5D.
The marking for the electronic equipment is:
II 2 GD EEx d II C T6 / T5 IP 66 T 85 / T100°C

Certificate only on request

ATEX Certification

ATEX

OXITEC® / COMTEC® electronic unit SME-5.
The marking for the electronic equipment is:
II 2G Ex d IIC T6 Gb IP 66 T 85 / T100°C

Certificate only on request

ATEX Certification

ATEX

OXITEC® 5000 Oxygen Measuring Probe Type KEX 5001 and KEX 5002.
The marking for the electronic equipment is:
II 2G Ex d IIC T3 Gb

Certificate only on request

ATEX Certification

ATEX

COMTEC® 6000 O2/COe Measuring Probe Type KEX 6001 and KEX 6002.
The marking for the device is:
II 2G Ex dIIC T3 Gb

Certificate only on request

ATEX Certification

ATEX

COMTEC® 6000 O2/COe Measuring Probes KES 6001 and KES 6002 in dust protection tube.
The marking for the electronic equipment is:
II 2D EEx IP 6X T133°C/T141°C

Certificate only on request

CENELEC Certification

ATEX

OXITEC® 5000 O2 Probe Ex version KES200Ex.
The marking for the electronic equipment is:
EEx d IIB T2

Certificate only on request

UL / CSA Panel Shop Approval

UL-CSA

(Carried out by the TÜV-Süd)
ENOTEC conforms to UL / CSA standards listed below:
UL 508A

Certificate only on request

Eurasian Conformity Mark

EAC

Conformity to all technical regulations of the Eurasian Customs Union assessment procedures and replaces the Gost mark.

Certificate only on request

Fieldbus interface specification

FIELDBUS

OXITEC ® 5000 und COMTEC® 6000 On request, systems can be delivered with certified modules to support this communication system.

Certificate only on request

HART interface specification

HART

Highway Addressable Remote Transducer (HART) is a standardized, widely used communication system for establishing industrial field buses. It allows digital communication between several OXITEC® 5000 or COMTEC® 6000 (field devices) on a common data bus. HART relies specifically on the also popular 4 / 20 mA standard (for transmission of analog sensor signals).

Certificate only on request

SIL
Safety Integrity Level

SIL

Safety Integrity Level (SIL) is defined as a relative level of risk-reduction provided by a safety function, or to specify a target level of risk reduction. In simple terms, SIL is a measurement of performance required for a Safety Instrumented Function (SIF). This certificate is only valid for current installations.

Certificate only on request

SIL2
Safety Integrity Level 2

SIL2

Safety Integrity Level (SIL) is defined as a relative level of risk-reduction provided by a safety function, or to specify a target level of risk reduction. In simple terms, SIL is a measurement of performance required for a Safety Instrumented Function (SIF). This certificate is only valid for current installations.

Certificate only on request

CE
"Communauté Européenne"

CE

In accordance with the safety and health requirements of the European Union.

Certificate only on request